Two


OK i said windows ill talk about them later so start with the side windows. Mine were leaking but not all but i re did the lot. I pulled off the rubber cover to reveal the pop rivets and using a 4mm drill bit i drilled out all the rivets. Prised out the window and cleaned up the two mating surfaces. Again used sikaflex to seal round the window frame and replaced. I used 4x12mm pop rivets as i feel they seal better than the shorter ones.


 This detailed drawing may give you an idea what is going on. L/H/S id the outer side and you can replace the rubber if its holed with gaps you can poke a finger through but that will be around £40 and then what someone skins you to replace. Well over 100 i would imagine. So, water runs into the rubber as its old and shrank in the sun. The water will sit in the rubber and rot your metalwork. It will also run along to the sides and down inside the rubber to the lower two corners. The 2.4 has its ECU under the passenger side as well as electrical parts like relays so get that sorted. The 2.5T the ECU is on the drivers side.


This is inside the van. I pulled back the screen rubber and as you can see, rust. I dried this out and treated with rust remedy before filling it up with sikaflex all the way along and down the sides.


See the trim hanging down over the screen and down the side pillar. Rip it out and bin it.


It sits in the rubber also and sooks up the water Holden it longer and rotten your van. I binned mine and replaced with the stretch carpet you get for the back when converting to camper. That stuck fine with spray glue and cut that to sit just over the screen rubber rather than tucked in.


Also the screen rubber has two ends what meet. Find this point and try and get a coat of sealent over it to make sure its water tight still. I have seen large gaps in this area.


Below is the area under the screen but with the plastic scuttle removed. Holding it in place is the nut from the window wipers and plastic rivets. The rivets pop into a rubber insert what in my van was letting in water. I took the rubber out the holes and binned them. The two middle holes i put a block of Sikaflex over them then........


....Covered them with a bit gorilla tape as that will stick and last for years even when wet. Try and get the top of the tape under the screen rubber itself for added watertight security.

You do not need the middle two as the scuttle is held in place with the wiper nuts.


The two side holes i drilled out to 10mm. Yes i am nuts, i drilled larger holes in my leaking van


Reason being i am adding a rivet nut. This is a rivet nut gun and a rivet nut what you screw into the end.


Then you pop the end into the hole and push the two handles together two or three times till tight. When you take screw the gun out you are left with a threaded hole


Replace the scuttle and then use a bolt and washer on the side holes. I need a larger washer and i also added a little Sikaflex on the bolt threads to give a little seal and act as a thread lock.


I cut the heads off the plastic rivets and stick over the holes in the scuttle. Now that mess you see round the wiper stalk. What i did when the scuttle was off was take the 2nd nut and washer off these and push them into the van but just enough to get a finger of Sikaflex round the inside. Pull it back out again and a bead of Sikaflex on the outside then replaced the washer and nut. Repeat other side. Some report that the water was getting down the middle of the moving part. I never had this but a dollop of grease should keep that at bay unless the linkage is well shot and wants replaced.


This area on both sides. The blue block is where the wing meets the window lower frame. Seal this off all the way round and down into bonnet. That can rot or the LDV sealant used would no doubt be all cracked now and letting in water what will reach the cab. The red is also just the odd spot weld and sealant what is now 16+ years old. Seal this up also on both sides.


What that arrow is pointing to it a dollop of old sealer just wrapped over the top of two folded sheets of steel that need a proper weld. You can also see a blob further down. Get that seam covered and sealed. The rubber you see running from left to right of van there is meant to touch the underside of the plastic scuttle. Even when done up the rain from roof and screen just runs down and over this and straight into your engine bay. When it start to run down the bulkhead what is a single skin it also soon makes its way into the cab. Cure below.........


To prevent the water getting into the engine bay look on ebay for 3M D shaped sticky back rubber. You get 3 meters for a couple of quid. Clean that rubber and run the sticky back stuff on top to made a dam for for the rain water. When you stick the plastic scuttle back on this will crush down the rubber making a seal and guiding the water to the side gutters.
Below is the side gutter what the scuttle gutter sits on. The black edge is meant to prevent water from running under it and onto battery tray and other side. It does not. Try and seal this also you have a screw holding the scuttle down. Other side and middle also. Water seeps through this also. You ever open the bonnet and see injector number 3 recess full of water? Middle screw is why. Fins rubber washers. Also the plastic scuttle itself should have a rubber running from left to right. This should cause a seal when you close the bonnet. It does not so again. More 3M D shaped rubber.