One

OK. I wrote this to assist others in looking for leaks in there Convoy's and probably the Pilot is the same crap design. If stuck with anything mail me at the bottom of the page. Not saying i have all the answers but willing to help


Personally i think the screen rubber gets blamed for more leaks than it should I was getting leaks in the cab after re sealing round the rubber with liquid rubber what was bugging the hell out of me so decided to investigate mote. Out with the overhead locker


Below is looking down you A pillar. (Each side of screen) Water runs forward under the gutter and unto the van and down the pillars. The N/S at the bottom is your relays and depending on what model your ECU. If you see water running down here or you see rust you need to act by reading on.


OK my gutters have been fully stripped of old sealer and re done with fresh Sikaflex and i still have leaks. See the red arrow below. This is a lip what looks like an L shaped strip of metal running the length of the van what is spot welded in place. The red arrow is the end of the l as the roof slopes down here but you still get the base of the L running the last foot or so (Yellow arrow). When raining one night s potted water seeping under this and running forward. What i did here was ordered a chemical called Captains Trolley what is not cheap at almost £10 a small bottle. I bought two. One for each side. The side you are working on get that into the kerb so the camber lets the chemical go into the L shaped metal. This runs into all the gaps and seals it. 
Right from back to front and wait an hour or so and do it again. Run some along the front over the screen also as this will run down into any gaps in the rubber. When done turn other side of van into kerb and repeat. Give both sides time to dry and run a bead of Sikaflex or the likes along the Lip and front of screen


If your gutter was guiding the water down the side of the screen rubber and you had holes this area is more than likely be where it comes out. Do not seal from the inside as this will just trap water and sit rotten away your metal what is needed to hold the screen in place. Always seal the outside first.


Now your gutter. As i said i did mine but this is what it looks like after about 16 month. I did try to keep the gutter profile to run the water away from the doors but since changed this. Ill explain in a mo.


Once you strip out your old sealant First cut your nozzle so you get a thin bead. Thin enough to get down that gap you see at the edge of the fibreglass. Pump lots down there so it oozes back up so pump fast but move up slowly. This will help your new sealer get under the fibreglass lip. Also along this gutter you have about three screws holding the roof down. Your sealer will crack over this area over time and let water in. What i did to prevent this was..............


........... When re filling the gutter after the initial bead to get under the lip cut your nozzle to pump out a large bead and over fill it. Imagine the left below was the profile how LDV did it. You want a slope like on the right (Yellow is sealer) Two reasons. You have extra sealer over the fixing screw to help prevent cracking and the water will just run over the gutters rather than along sending it down the screen or sitting in puddles waiting to seep through. Also remember and do up and over the back doors.


Now all this water will be going over your side doors and windows. Ill get onto this later.
Do you still have this roof vent/fan? It leaks, even if yours does not just now it will and it will be after you have converted your van and all over your bed. Take it out...


... When out you can get a fibreglass kit what should have enough to cover the hole for around £13 - 14. you get it at Halfords, B&Q, motor factors possibly or ebay. Davids Glass Fibre Kit its called and also a couple of sheets of fine wire mesh for support. Its an easy enough job to do and best done working from the outside. 


Below is what my van looked like when done. You can not bother with the kit and get a pop up skylight from around £50. I put one in but closer to the middle hence covering the hole.


OK the water running over the gutters and onto the doors. Here is a length of J shaped alloy gutter from ebay for under 30 quid. This covers both  doors. Drivers door i just bought a section of the rubber gutter you get for caravan doors. Its sticky back but i also used Sikaflex and self tappers. I dont have water coming into the van here. Ill explain best way to re seal the windows later.  



Back doors leak. This red arrow is where the back door side slops and meets the outer side. LDV came up with the bright idea to use two seals and you are left with this gap. If your doors have dropped at the hinges or door strikes in the roof or floor then they will not be closing tight and water will get in here. My leak was working its way round and onto the cable tray making me think the gutter was leaking.  Look at the hinge where it bolts to the door. Look round bolts and any sign of un painted steel then there is a very good chance its moved. Loosen bolts and adjust.


This is the door strike. Loosen these and push back into the van as far as possible and tighten. 


Do the same for the floor ones. You may need heat with these. Once done test doors to make sure they are closing properly and you have an even gap all the way round. 


Talking door is your side door letting in water and has a large gap at the top? This is the top runner and that Allen bolt and nut is the up and down adjuster. You are best loosening the bolts on the middle and bottom runner before adjusting. Wind this up and the door should go up also but if the door seal is shot no adjusting will keep the water out. Replace it.


The middle runner that runs along the side of the van. Look inside the van and you can see bolts to take the runner guide out. Mine was starting to let in water so i managed to get away with rust treatment and smear with sealant.